What length is best? Is it possible to go too short? Are long stems good for anything at all? All the answers are here.


Length is everything


A MTB bike stem’s stated length is not simply the length of the whole stem front-to-back. Stem length is measured from the middle of the headset stem cap bolt to the middle of the handlebar. Got it? Good. See the pic below for how to measure (it’s a 70mm stem).


Stem length affects how all bikes ride but stem length is extremely significant when mountain biking. It is one of, if not THE most important aspects that governs how a bike handles.


A bike without enough reach can be uncomfortably cramped and prone to wandery climbing. Your bike’s top tube length is going to dictate just how short you can go before you start to encounter too many negative handling traits.


If you have a bike with a short top tube then putting a short stem on it will probably not result in good handling. It will be like riding a bike that’s too small for you. You will find it hard to ‘work’ the terrain and you’ll be generally unbalanced from being so upright.


On most modern mountain bikes you should be aiming for a stem length somewhere between 50mm and 80mm.


A quick note about handlebar width


Handlebars work in conjunction with stems to dictate where your hands end up and thus your overall front end weighting and positioning.


Some riders switching to a significantly shorter stem will benefit from also increasing their handlebar width. It’s a bit hard to explain why here but basically it keeps a bit of the overall reach that they’re used to but adds stability and control.




Stems come in different amount of rise ie. the angle of the stem’s body. Because stems have got shorter over the years, rise doesn’t actually make that much of a difference to bar height any more. There’s only so far up or down a stem can go when it’s short in length.


With mountain biking your front end height is now much more dictated by your handlebars. If you want a higher front end, you need bars with more rise to them. If you want a lower front end, you should try some flat bars.


If in doubt the best place to start is a stem of around 5-6 degrees. Or a zero degree stem if you’re considering a stem shorter than 70mm. This gives a nice neutral placing of the bar clamp area without committing you to an overly tall or low front end.


Bar diameter


Bar clamp diameter is the diameter of the handlebar where the stem clamps on to it ie. the middle.


If your mountain bike is even remotely new it will have a handlebar clamp diameter of 31.8mm. The previous standard diameter size was 25.4mm. If you’re unsure just grab hold of a tape measure or a ruler and have a quick look. It’ll be obvious which of these diameters it is.


Because this is the mountain biking industry and we love introducing new ‘standards’ every five minutes there is now another new clamp diameter standard on the market: 35mm.


If you want to add even more stiffness up front then consider making the move to 35mm. Bear in mind that you’ll need a new handlebar as well as a stem and they’re currently aren’t that may companies supporting the 35mm size just yet.




Virtually all stems are made from aluminum. Steel is reserved for super cheap bikes and kids bikes. Titanium used to be in vogue in the 90s but these days carbon fiber is the material of choice for those with more money (than sense).


CNC machined aluminum stems cost more than forged and welded stems but they often stiffer. Some people also just like the look of CNC’d stuff.


Clamp design


There are two clamps on a stem. A handlebar clamp at the front and a fork steerer clamp at the back.


Almost all decent stems use a 4-bolt design for the front bar clamp. Strong, stiff and less creak-prone than old fashioned 2-bolt face plate designs.


The rear clamp – where the stem fits on to the fork steerer – sees a tiny bit more variation in design. The vast majority use a 2-bolt design. Some DH stems use a big single bolt at the back. Some longer XC stems use a wedge design with the bolt situated in the body of the stem in front of the fork steerer.


It’s a good idea to look out for a stem that doesn’t have rear clamp bolt heads that protrude too far out. These can really hurt your knees if you crash. Most decent stem designs have cowled or rounded-off bolt head designs.


Which MTB bike stem should you buy?


Leisure riders – Don’t worry too much about weight and clamp design. Get a 80mm or shorter stem that fits your handlebar and that’s it. As usual, check the sale sections for bargains.


Regular riders should try as short a stem as their bike frame’s top tube allows before it gets too cramped. There are not many riders who’ve regretted slapping on 60-70mm stem and enjoying the immediate handling benefits.


Racers will want to avoid heavy stems but the key quality they should look for in a stem is stiffness. CNC stems should be on your shortlist. Spendy racers may wish to consider carbon. There’s also the new 35mm standard if you don’t mind buying a new handlebar as well.


G-MA Engineering Co., Ltd. is the experienced and professional manufacturer of MTB bike stem and other related bike parts. For more information about bicycle part series, welcome to browse the website of G-MA and feel free to contact with them!


Article Source: https://www.merlincycles.com/blog/buyers-guide-to-mountain-bike-stems/